Fire Hose and Fittings

UL Listed Fire Hose and Fittings, Shipped Across Canada

When a wildfire advances or a hydrant needs service, the hose and hardware have to be on hand before the work starts. Cleanflow supplies fire hose and fittings to fire departments, forestry crews, municipalities, construction sites, and industrial plants across Canada. One purchase order can cover everything: complete hose assemblies, bulk hose by the foot, adapters and couplings, nozzles, valves, and hydrant tools, with UL-listed and NFPA-compliant hose throughout.

Fire Hose Assemblies

Ready-to-use assemblies arrive with couplings already attached and rated to the hose. Choose a single jacket for lighter duty or double jacket for hard service.

1-1/2" Single Jacket Fire Hose Assemblies with Forestry Fittings

1-1/2" single jacket fire hose assemblies are the working standard for forestry, rural protection, and light industrial lines at 150 PSI. The quarter-turn instantaneous couplings have non-gendered ends, so any hose joins any other in seconds.

1-1/2" Double Jacket Fire Hose Assemblies with Brass NPSH Fittings

Double jacket fire hose assemblies add a second woven cover over the first, which lifts working pressure to 300 PSI and shields the hose from abrasion. Brass NPSH swivel couplings rotate freely, so you can tighten the connection without twisting the hose.

Bulk Fire Hose by the Foot

Crews that couple their own lines can buy hose cut to length in 1" through 2-1/2" diameters. Choices include double jacket, potable water hose rated to MIL-H-24606B, and red nitrile hose listed to NFPA 1961 and ULC S511-14.

Single Jacket Industrial and Forestry Hose (Hose Only)

Single jacket hose by the foot is the economical base for crew-built lines. The synthetic jacket resists rot and mildew, so it can be rolled up wet at the end of a job.

Yellow Lightweight Forestry Hose (300 PSI)

High-visibility yellow forestry hose is easy to spot in smoke and brush, and carries a 300 PSI rating while staying light enough to pack in on foot.

Adapters, Couplings, and Repair Parts

Forestry instantaneous adapters, NPSH couplings, shanks, caps, and replacement gaskets keep mismatched equipment connected and old assemblies in service instead of in the scrap bin.

Fire Hydrant Hose and Hydrant Fittings

A fire hydrant hose connection starts with the thread. Municipal hydrant threads vary between cities; the right adapter, a fresh gasket, and matching hose close that gap.

Hardcoat Aluminum Fire Hydrant Adapters

Hardcoat aluminum fire hydrant adapters bridge 2-1/2" hydrant threads to standard male NPT and come in male and female configurations. The hardcoat finish fights the corrosion that seizes bare aluminum on outdoor hydrants.

2-1/2" Fire Hose Assemblies with Hydrant Threaded Ends

2-1/2" hydrant-threaded fire hose assemblies connect straight to the hydrant port for flushing, maintenance, industrial washdown, and firefighting duty. Single jacket covers routine work; double jacket handles heavy service.

Paired with a wrench and a gate valve, one hydrant becomes a controlled water source for an entire site. That is why contractors treat fire hydrant hose as standard site equipment, not emergency-only gear.

Fire Hose Nozzles

Thermoplastic Fog Nozzles

Fog nozzles shape the stream for knockdown and cooling without the weight or cost of metal. Brass NPSH fog and tapered nozzles are also stocked for crews that standardize on metal.

Fire Hose Valves and Water Thieves

Y valves split one supply line into two attack lines at up to 300 PSI, and water thieves tap a garden-hose outlet off a forestry line without shutting it down. These fire hose valves keep one water source feeding several jobs.

Full Port Fire Hydrant Gate Valve, 2-1/2"

The full port fire hydrant gate valve installs on a 2-1/2" hydrant outlet to control flow and pressure without choking the waterway. The body is anodized aluminum with bronze seats, stems, and gate.

Hydrant Wrenches and Tools

Reed HWB Adjustable Hydrant Wrench

The Reed HWB hydrant wrench is cast ductile iron with corrosion-resistant plating, and fits pentagon nuts to 1-3/4" and square nuts to 1-1/4". Forged steel, ratcheting, and Storz-cap wrenches are stocked alongside hydrant flushing assemblies and marker poles.

Choosing Fire Hose for the Job

Start with duty level. Forestry and rural protection lines favour light single-jacket hose that packs tight and carries far; municipal and industrial service favours double-jacket construction that survives rough ground and runs at higher pressure.

Then match the thread standard your equipment already uses: NPSH, hydrant thread, garden hose thread, or forestry instantaneous. Buying assemblies gets you working lines immediately; buying bulk hose and couplings costs less per foot when your crew builds its own lengths.

A Fire Hose Supplier That Ships Across Canada

Cleanflow Utility Supply Company has supplied fire hoses to Canadian municipalities, fire departments, forestry crews, and contractors since 2001. Stock is held in Canada, and orders ship to every province. That matters most in the British Columbia Interior, where crews in Kamloops, Vernon, and the Okanagan face wildfire season every summer. Construction and industrial buyers can call for volume pricing on larger orders.

Every hose and fitting shows its own UL and NFPA listings, so procurement teams can check the exact certification before they buy.

Buy Fire Hose and Fittings Online from Cleanflow

Cleanflow Utility Supply Company delivers fire hose and fittings across Canada and the USA, with free shipping on orders over $199 and returns accepted within 30 days. Buy online, or call 1-866-335-1078 to sort out thread questions or match hose to your hydrant standard. Buying domestic means no customs surprises and no waiting at a border crossing when the season turns.

Frequently Asked Questions

What are the standard fire hose sizes?

Common fire hose sizes are 1 inch, 1-1/2 inch, 2 inch, and 2-1/2 inch inside diameter. Attack and forestry lines typically run 1-1/2 inch, while hydrant supply lines run 2-1/2 inch. Bulk hose in this range can be cut to length by the foot.

What are the different fire hose thread types?

The main fire hose thread types are NPSH (National Pipe Straight Hose), NH or NST fire hose thread used on hydrants, GHT garden hose thread, and quarter-turn forestry instantaneous couplings. Hydrant threads vary by municipality, so adapters are often needed between systems.

What is the difference between single jacket and double jacket fire hose?

A single jacket fire hose has one woven cover and typically carries a 150 PSI working pressure, which suits forestry and light industrial work. A double jacket fire hose adds a second woven layer, raising working pressure to 300 PSI and abrasion resistance for municipal and heavy industrial service.

What fittings do I need to connect a fire hose to a hydrant?

You need a hydrant adapter that matches your municipality's hydrant thread on one side, usually 2-1/2 inch, and your hose or pipe thread on the other, plus a fresh gasket and a hydrant wrench to open the hydrant. A gate valve adds flow control at the outlet.

What does UL listed and NFPA compliant mean for fire hose?

UL listed means the hose or fitting has been tested by Underwriters Laboratories against its safety standard. NFPA compliant means it meets the National Fire Protection Association's specifications for its product class, such as NFPA 1961 for fire hose.