HCP AN-21.5H High Head Submersible Dewatering Pump: 1.5 HP, 2-inch, 73 ft Head

HCP AN-21.5H 1.5 HP High-Head Dewatering Pump for Deep Pits

Product Overview

The HCP AN-21.5H is a high-head submersible dewatering pump, the high-lift member of HCP's 2-inch AN line. Its 1.5 HP motor moves muddy and silty water up to 73 ft of head at up to 88 GPM, clearing deep excavations, high-rise transfers, and long discharge runs that stall a lower-powered pump.

Quick Specs

• Horsepower: 1.5 HP (1.1 kW)
• Voltage / Phase: 120V 1-phase (14.4 A), also 240V 3-phase (4.6 A) and 575V 3-phase (1.8 A), 60 Hz
• Discharge: 2 inch (50 mm), Female NPT
• Max Head: 73 ft
• Max Flow: 88 GPM
• Solids Handling: 5/16 inch (8 mm)
• Impeller: Cast-iron vortex
• Cord: 30 ft, 3-prong 120V plug

Key Features of HCP AN-21.5H High Head Dewatering Pumps

• With 1.5 HP the AN-21.5H reaches about 73 ft of head, roughly seven storeys of lift, so it clears deep excavations and long vertical runs that stall a 1 HP dewatering pump.
• As a high-head submersible dewatering pump, it is built for lift, not extra flow. Like the 1 HP AN-21A, it peaks near 88 GPM, but the added half-horsepower pushes that water far higher.
• A cast-iron (FC200) vortex impeller and casing stand up to abrasive, silty, sandy water, where the plastic impeller on the 1 HP AN-21A would wear faster. Solids up to 5/16 inch (8 mm) pass through the 304 stainless steel bottom strainer.
• Twin mechanical seals, carbon/ceramic over silicon carbide, run in an oil bath to keep grit and water out of the motor. The three-phase models add a built-in auto-cut thermal protector against overload.
• The IP68 sealed motor, with a 304 stainless steel frame and cast-iron body, is rated for continuous submersion to 33 ft (10 m) at 120V, 240V, and 575V.

Specifications

Performance Overview

The AN-21.5H is a high-head submersible dewatering pump, so it lifts to about 73 ft, well above the 1 HP AN-21A, while both peak near 88 GPM. Flow is highest at low lift and tapers as head rises, so match the pump to the vertical distance you need to clear.

AN-21.5H vs AN-21A: Do you need the extra head?

Both are 2-inch AN dewatering pumps that peak near 88 GPM. The AN-21.5H adds lift and a tougher impeller. Choose based on how high you need to push the water and how abrasive it is.

Applications

As a high-head submersible dewatering pump, the AN-21.5H suits jobs where water has to move up and out:

• Deep excavation and foundation pits that need high lift
• Pumping water up from basements and sub-levels to grade
• High-rise and multi-storey construction dewatering
• Long-distance or uphill discharge runs
• Muddy, silty, and sandy water from sumps, vaults, and cofferdams

Run the 2-inch discharge into a 2 inch layflat discharge hose to carry water clear of the work area.

Buy the HCP AN-21.5H High Head Dewatering Pump Online from Cleanflow

When water has to climb out of a deep excavation, a flooded sub-level, or a long uphill run, the HCP AN-21.5H submersible dewatering pump delivers up to 73 ft of head on 1.5 HP, with a cast-iron impeller built for silty, abrasive water. Cleanflow Utility Supply Company is an authorized HCP dealer, stocking and shipping HCP pumps across Canada and the continental USA, with free shipping on orders over $199.

Browse the full submersible dewatering pumps range to compare flow and head, then add the AN-21.5H to your cart or contact us to size the right pump for your lift.

Frequently Asked Questions